A Beginner's Guide to Plumbing for Bathtub Installation
A Beginner's Guide to Plumbing for Bathtub Installation
Blog Article
On this page down the page you'll find some worthwhile information on the subject of A Step-by-Step Guide to Installing a Bathtub.
:max_bytes(150000):strip_icc()/installing-a-tub-or-shower-surround-2718986-hero-40160398595d4544b639b3398cdb247c.jpg)
Mounting a tub isn't exactly rocket science, however it does require solid plumbing, woodworking, and also sometimes, tiling abilities. Changing an old bathtub with a new one is additionally a reasonably challenging project. If the old tub is easily obtainable, the job can move quickly; if you need to open up a wall to eliminate the old tub and also position the brand-new bathtub, the job is a lot harder. In either case, the task is within a home handyman's abilities, although you will require an assistant to leave the old tub and set in the brand-new one. See to it you have actually certified yourself for the task and are comfortable attempting it. As opposed to working with a service provider to take control of a halfway-completed job, it is much better to consider using one before you begin. Opportunities are you might require a specialist plumber to make tube links.
This article will certainly aid you mount a brand-new bath tub in your shower room if you have actually already bought a new tub and also don't require to alter the plan of your previous water pipes.
Your devices and product list need to make up the following:
Planning for the Installation
To start with, the supporting frame provided with the bath ought to be fitted (if needed) according to the maker's directions. Next, fit the faucets or mixer to the bath tub. When fitting the tap block, it is essential to make certain that if the tap features a plastic washing machine, it is fitted between the bath as well as the faucets. On a plastic bathroom, it is additionally sensible to fit a supporting plate under the taps unit to avoid pressure on the bath tub.
Fit the flexible faucet adapters to the bottom of both faucets making use of 2 nuts as well as olives (often provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and after that pass the electrical outlet via the hole in the bath. Make use of the nut provided by the manufacturer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the flexible overflow pipeline to the overflow outlet. After that, screw the pipe to the overflow face which must be fitted inside the bathroom. Make sure you make use of every one of the provided washers.
Attach the catch to the bottom of the waste outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Connect the bottom of the overflow tube in a comparable manner.The bathroom ought to currently be ready to be fitted in its final position.
Removing Old Taps
If you need to change old faucets with brand-new ones as a part of your setup, after that the first thing you must do is disconnect the supply of water. After doing so, turn on the faucets to drain pipes any type of water staying in the system. The process of eliminating the existing taps can be fairly troublesome due to the limited accessibility that is frequently the instance.
Use a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that links the supply pipes to the faucets. Have a towel all set for the continuing to be water that will certainly originate from the pipelines. As soon as the supply pipelines have actually been eliminated, utilize the very same device to loosen the nut that holds the taps onto the bath/basin. You will certainly require to quit the solitary faucets from turning during this procedure. As soon as the faucets have actually been eliminated, the holes in the bath/basin will need to be cleaned of any type of old sealing substance.
Prior to moving on to fit the brand-new taps, contrast the pipeline connections on the old faucets to the brand-new faucets. If the old faucets are longer than the brand-new faucets, after that a shank adapter is required for the new taps to fit.
Setting up the Tub
Utilizing the two wood boards under its feet, put the tub in the required placement. The wooden boards are valuable in uniformly spreading out the weight of the bath tub over the area of the boards as opposed to concentrating all the weight onto four tiny factors.
The following objective is to make certain that the bath tub is leveled all round. This can be accomplished by inspecting the level as well as readjusting the feet on the bath tub up until the spirit level reads level.
To install taps, fit the bottom of the furthest adaptable faucet port to the suitable supply pipeline by making a compression sign up with; then do the exact same for the various other tap.
Switch on the water and also check all joints and brand-new pipework for leakages and tighten them if essential. Fill the bath tub and additionally check the overflow outlet as well as the regular outlet for leakages.
Lastly, repair the bathroom paneling as defined in the supplier's instruction manual. Tiling and sealing around the tub ought to wait till the bathtub has actually been utilized a minimum of when as this will certainly settle it into its last placement.
Fitting New Taps
If the tails of the brand-new taps are plastic, after that you will certainly require a plastic port to avoid damage to the string. One end of the port fits on the plastic tail of the faucet as well as the various other end gives a link to the current supply pipelines.
If you need to fit a monobloc, then you will certainly require lowering couplers, which links the 10mm pipe of the monobloc to the basic 15mm supply pipeline.
Next off, position the faucet in the installing hole in the bath/basin ensuring that the washing machines are in location between the faucet and also the sink. Secure the faucet in position with the supplier provided backnut. When the faucet is securely in position, the supply pipes can be attached to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with typical faucet ports. The previous kind must be connected to the tap finishes initially, tightening just by hand. The supply pipes can later on be connected to the other end. Tighten up both ends with a spanner after both ends have actually been linked.
Tiling Around the Tub
In the location where the bathroom satisfies the floor tile, it is essential to seal the joins with a silicone rubber caulking. This is important as the fitting can relocate sufficient to split an inflexible seal, creating the water to penetrate the wall in between the bathroom and also the tiling, bring about difficulties with moisture and possible leakages to the ceiling below.
You can select from a selection of coloured sealants to assimilate your components and also installations. They are marketed in tubes as well as cartridges, as well as can sealing gaps up to a width of 3mm (1/8 inch). If you have a bigger space to load, you can load it with twists of soaked paper or soft rope. Keep in mind to constantly load the bathtub with water before securing, to permit the motion experienced when the bathtub remains in use. The sealer can split fairly early if you do not take into account this motion prior to sealing.
Conversely, ceramic coving or quadrant tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are additionally conveniently readily available on the marketplace. It is advisable to fit the floor tiles making use of waterproof or water resistant sticky and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a keen reader about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround, I think sharing that piece of content was really useful. Appreciated our content? Please share it. Let other people discover it. Many thanks for your time. Come back soon.
Get A Free Estimate Report this page